Jockeygolf's 2011 STI Sedan Build by jockeygolfs

By diyauto
( 4 )

10 minute(s) of a 118 minute read

8-12-2011

Jockeygolf's 2011 STI Sedan Build


Compliments of jockeygolfs @ nasioc.com


8-12-2011




NEW COMPLETE LONG BLOCK BEING BUILT 08/15:


New Case Halves w/ Outfront Closed Deck, 1/2" head studs, pinned mains

Pauter X Beams

CP Pistons w/ Coated Crown

OEM Crank

King Bearings

12MM OEM Oil Pump


New Heads

Ferrea Comp Plus Standard Valves

Ferrea Dual Valve Springs

Ferrea Tooled Steal Retainers

Ferrea Valve Locks

Kelford Dual AVCS Cams


Every sensor, bolt, pump, etc is brand new on this long block. 




Quick List of Parts as of August 15': 




ECU:


Cobb Accessport V3 




Block: 


Cosworth 8.2 99.5 Pistons 


Cosworth Rods ACL bearings 


OEM Crank New case halves 


Stock heads ARP Head Studs 


12mm Oil Pump 


Killer B Pick up 


Killer B Baffle 


Grimmspeed Thermostat 


Techna Fit SS Power Steering Line w DEI Fire Sleeve 


Koyorad Radiator



Exhaust: 


ETS Bigass Headers 


ETS Uppipe Wrapped in DEI silicone coating and Titanium Heat Wrap 


ETS Downpipe Wrapped in DEI silicone coating and Titanium Heat Wrap 


Invidia q300 cat back 


Tial 44mm External Wastegate 




Intake: 


4" K&N Filter (ETS Rotated Kit) 


Spec C TGV Deleted 


Grimmspeed 3mm Phelonic Spacers 


ETS 4" Front Mount Intercooler 


Tial Q 50mm Blow Off Valve 




Turbo: 


Precision Turbo 6262 BB .64 A/R V-Band


Grimmspeed EBCS 


PTP Turbo Blanket 




Fuel: 


DW65 Intank 


Radium Engineering Surge Tank w/ Walbro 465 E85 Pump -6AN and -8 AN PTFE Lines 


Five0 1200 injectors 


NGK 1 Step Colder Plugs gapped .022 


Fuelab High Flow Large Seat Fuel Pressure Regulator 


Aeromotive Fuel Rails and Stainless Steel Lines 


Aeromotive Fuel Pump Controller


Autometer Tach Adapter


Aquamist HSF-3 V2 


Howerton Engineering (2) 1 Gallon Tank setup 


-4AN Meth lines and No Drip Disconnect and Weatherpack 




Gauges: 


Smycluster Maker center bezel 


JCS-Pods A-pillar 3 gauge pod 


AEM UEGO AFR 


AEM Oil Temp Gauge 


Defi Oil Pressure Gauge 


Defi Fuel Pressure Gauge 


Aquamist Injection Gauge 


Perrin Oil Filter Sandwich Adaptor 




Exterior: 


HT Autos Front Lip 


HT Autos Side Skirts 


HT Autos Rear Diffuser 


HT Autos Rear Skirts 




Transmission: 


Exedy Triple Disk Clutch (cerametalic) 


TIC Holy Shift Kit w Kartboy short shifter 


Group N Pitch Stop 


Group N Engine Mounts 


Group N Transmission Mount 


Whiteline Positive Shift Bushings


Whiteline Rear Diff Bushing


Whiteline Rear Diff Outrigger Bushing

Whiteline Rear Subframe Inserts




Brakes: 


Stop tech Pads 


Dba T2 slotted rotors




Suspension:


Fortune Auto 500 8k/8k w radial bearings


SuperPro Roll Center

SuperPro Front and Rear Trailing Arm Bushings


SPC Rear Lateral Control Arm


SPC Rear Toe Arm


Whiteline Caster/antilift Bushings


Whiteline Front Control Arm Front 

Inner Lower Bushings


Whiteline Steering Rack Bushings


Whiteline 22mm Front Sway Bar


Whiteline 22mm Front Sway Bar


Kartboy Front Endlinks


Kartboy Rear Endlinks


2015 STI Steering Rack 13:1




Wheels:


Advan RZ 18x10 +35


Nitto NT555 255 35 


Project Kics R40 Lugs




I have a pretty long and winded thread in the Newbies and FAQs titled "Loaded COBB AP Stage 1 93 oct in 2011 STI!! I've come a long way from that first post and want to just compile it here. I'll do my best to put everything down chronologically and with links to the photos. I want to thank all the people who have given me constructive advice etc throughout my journey on that thread. Hope you guys follow me here. I want to thank the following people/companies for all their help (if I forgot you and you want to be listed please shoot me a PM): Phatron STIMikey Jdub.csu Smeerone Tenacious Bee Xluben Themaus Wrx02ftw Rallyspec Realstreetperformance Rallysport Direct Perrin Flatironstuning Boston Motorsports IAPerformance Aquamist Howerton Engineering Bertune TAV Racing I purchased my car towards the end of September, 2010: Sitting in the driveway 



 

Out at one of my job sites

 

Shortly after purchasing the car I began researching the possible mods that I could do but try to keep the car as stock as possible. The most obvious choice was to purchase a Cobb Accessport and flash to stage 1. I enjoyed stage 1 for probably...1 month. It was then time to go to stage 2. I purchased the following: Perrin Equal Length Headers Perrin Up Pipe Cobb Down Pipe AEM Intake

 

At this time I knew that an off the shelf map would not do. After a ton of research on tuners in my area, I turned to e-tunes. Given the track record of this gentleman I decided that I would put my baby in the hands of Phatron of Phatbotti Tuning. This was my first time ever working on a car and thankfully a friend of mine was willing to help me. An extra plus was that his father has a garage with a lift at his house. The install occured sometime in November/December, 2010: On the lift

 

OEM Parts a plenty

 

Header installed

 

Down Pipe installed

 

Tuning commenced shortly afterwards. What an experience. We started on 2nd gear doing pulls from 2,000 RPM to 7,000 RPM. Several pulls later it was time to move to 3rd gear. It is about 9 pm and I do a pull and then...BOOM!!!!! WTF!!!!! Lights were flashing, the car was limping and I was peeing my pants!! I pull into my neighborhood and quickly pop the hood and begin texting Phatron like a mad man. All the hoses looked ok. Turns out, this was my first time experiencing boost cut! We hit 23 PSI which was what Phatron had set the cut at. Whew! When all was said and done, several nights of pulling up till 5th gear on the highway, we were done. From what I remember we were at about 280ish WHP/TQ using Airboy to calculate the road loads. A decision was then made to upgrade the stock boost control system and the By Pass Recirculation Valve sometime in December, 2010: Grimmspeed 3 port Electronic Boost Control System

 

Forge By Pass Recirculation Valve

 

Retune w/ Phatron. I knew this would not be enough for me. It was fun but I wanted more. Research began on what the stock engine could be pushed to. 400 WHP was the limit that I found consistently. So my focus was on a quick spooling turbo and the required supporting mods. I purchased in December, 2010: Please keep reading the following posts to see the rest of the progress. I had to chop up my original post in order to insert pics rather than just having links.


Blouch Dom 2.5XT-R




Deatschwerks 850 Injectors

 


Walbro Fuel Pump

 


NGK 1-step Spark Plugs

 


Perrin Turbo Inlet



KStech 73mm Cold Air Intake

 


I was a little side tracked after purchasing these items when Invidia released their quad tip exhaust for the sedan. I had to get it and I was not going to leave the bottle neck in the exhaust so the Cobb had to be replaced by the Invidia Down Pipe. The purchase was made and exhaust installed in January, 2011:


Silicon Coated the Down Pipe

 


Titanium Wrap Down Pipe



Exhaust Installed

 


More tuning with Phatron shortly afterwards.


Okay, back to the turbo and the other parts. Before I can do that I had to get an AFR Gauge. I didn't want to mount the gauge just anywhere so I had to go with something that was as OEM looking as possible. With that, I had to fill the second gauge bezzle so an Oil Temp Gauge was purchased. I know I know, an Oil Pressure Gauge will be coming soon:


AEM AFR Wideband Gauge

 


AEM Oil Tem Gauge



SMY Cluster Bezzle

 


Perrin Oil Filter Adaptor

 


Gauges being installed

 


Gauges Installed

 


We are now ready to go with installing the turbo now that the AFR Wideband is installed. This happened sometime in April, 2011:


Holy crap, my engine bay is a mess!

 


Intake Manifold is off




Comments

Great build and details!

Posted by Diggymart on 2/20/19 @ 1:21:20 PM