How to install RedlineGoods door inserts Honda Civic gen 5 (92-95)

By diyauto
( 1 )

7 minute read

Shift boot store


How to install RedlineGoods door inserts Honda Civic gen 5 (92-95)

Door panel removal

Remove all screws that attach the door trim to the door by starting with the power windows. Unscrew the screw at the bottom of the small compartment:

Once unscrewed, unplug the wire of the power window if you have it.

page1image928768848


page1image928769456


Now unscrew the door handle, the screw is hidden by the handle, pull it to access the screw.

page2image927712448


Then rotate the cover of the handle to take it out of the slot.

page2image998248752


Now you can remove the door panel. Start by pulling the door panel to unclip it from the door. There is approximately 10 clips around the door. Start with the bottom left side, easier side to unclip.

Continue to unclip the all way. Pull it out by the top.

page3image998293088


page3image998293696


Replace the coating :

On the back of the door ponel, you can see how the armrest is attached. Most likely glued.

page4image998759824


Simply unplug the armrest to the door trim by pulling it (if it is fixed by glue).

page4image998771840


page5image998770800


Now remove the black plastic part starting with the three rear screws.

page5image998273936


The rear side is old with two clips on the two sides. Care when you unplug it, they are a bit weak.

page6image998742992


Now remove the two screw who old the pastic to the door panel. Then put out all the plastic.

page6image998754448


You can now remove the coating by pulling it off.

page7image927290208


If necessary you have to correctly empty the glue hole because residues can prevent cored bond when you reinstall the panel back into the car.

page7image999229040


Here is the correct way to have your supports cleaned before adding the new leather.

page8image999266992


You can now place your new fabric and correctly position on the liner. Take care of fixing it well in the corners in order to be in its final position.

page8image999210912


Carefully cut the fabric in places where the plastic door must be reattached. Make sure to leave enough margin. You can always trim off more when necessary. An X-acto knife is the best tool for this purpose.

page9image930992624


page9image930993008


Add the bottom plastic to his previous place in order to keep the fabric in good position during the bonding phase.

page10image972717456


Then screw the plastic back to the armrest, the fabric cannot move anymore so it will be easier to glue it properly to the other parts of the door.

page10image972722176


Now start the bonding phase with a tube of glueneoprene glue, do not hesitate to put a lot of glue to prevent bubbles from forming. Make sure the entire area is evenly covered with glue.

page11image972580768


On corners of the door, the fabric should be taut and absolutely must keep the position you give it.

page11image972515088


Repeat the same procedure for the top of the armrest

page12image972402400


Your fabric is now properly glued, now you just have to re-assemble plastics elements back into the car.

page12image972589296


Reassemble the plastic lower storage and don't forget to cut the fabric all around the holes

page13image972372592


Reassemble the door panel

Now you have to pick up the armrest to the door trim part, it is advisable to raise the door trim part on some supports (chairs, anything really) in order to fix and let the glue dry properly on the armrest.

page13image972093840


Put the armrest on the door trim making sure it is correctly positioned.

page14image972243952


Then fix the armrest door trim filling hole with glue neoprene.

page14image972569264


Let dry for a full day before remount the door panel. Then proceed to reassemble the door. For convenience, remove first the plastic cover mirrors if you have not done it before.

Reattach the trim in the same way that you removed, taking care to re-clip all the edges on the door side. Then replace, in first, the plastic of the window controller taking care to plug it back.

page15image972316640


page15image972317248


Finally, reassemble the door handle by screwing the cover.

page16image999017632


Enjoy the result !J

page16image999201520


BUY THIS PART HERE!


Comments