The Wifes Worst Nightmare 83 Full Resto by Minidarren83

By diyauto
( 3 )

5 minute(s) of a 192 minute read

9-19-2015

New gearbox build underway

20150919_214646_zpsylqxjtrf.jpg

New lsd diff new 3rd 4th and 5th gears going in

20150910_165504_zps8zeo3e6q.jpg


9-21-2015

And all done

20150921_133446_zpskewdywsl.jpg

Garage looks a little messy now lol

20150921_133455_zpsfsfhhjny.jpg


9-24-2015

Thus arrived today I am going turbo!!!

20150924_124228_zpszzq7kpck.jpg


10-12-2015

So in the last few weeks I've broken a hilo



Fixed this and then last week drove over 600 miles trouble free all finishing with a day at santa pod on the strip. It was very busy only getting 6 runs in

20151010_152719_zps0zowldij.jpg

Here is my first run

https://m.facebook.c...71&id=506417470

That's my mate in his new focus st I fluffed the start but reeled him in to win


10-17-2015

Mot too sure about the new wheels maybe a splash of black might help

20151015_143945_zpsoif430b8.jpg

20151015_144048_zpsdkwqwh7u.jpg


10-27-2015

I've been shopping for the turbo swap

20151027_190541_zpssxm38acl.jpg

Just a few bits left some more silicone hoses and manual boost controller then I can start getting on with it


11-30-2015

Took the car off the road for the winter and to do the turbo conversion

20151118_173801_zpskrghiwgi.jpg

Bought a mg zr turbo conversion to use as my winter run around

received_10153885550138643_zpspz9brrqt.j

received_10153885550108643_zpszmaqnepa.j

20151118_174242_zpsskqqzurk.jpg

Not bad for a winter runaround


2-6-2016

A few changed and additions over winter

New rear seat for the kiddies

20160104_002317_zpsy4lhadsz.jpg

And a new t7 heater with an mg resistor pack fitted so I can have 4 speed

20160206_184010_zpsxbvjzby2.jpg

20160206_183934_zpsfycwqbvq.jpg

The turbo would just not fit even after cutting **** loads out of my front so copied Pete and made this type of manifold

20160206_183838_zpspjrq410f.jpg

With the engine back in the car I can work out the last but of the manifold

20160206_215414_zpstvtz3j8o.jpg

And it now fits inside a standard clubby front just means I need to fix all the holes I cut and repaint

20160206_221004_zpscysawahf.jpg


2-7-2016

No not yet I don't have any water in the system

Bit more done finished the manifold and git the turbo mounted

20160207_203620_zpsetgqwmrb.jpg

I ended up welding the flange to the manifold to secure its position before making up the small link piece with a toilet roll tube

20160207_171009_zpshmgye8ro.jpg

20160207_205121_zpsxekygaov.jpg

A good bit of clearence to the oil filter and the exhaust just goes where it should

20160207_205140_zpspwqqwfep.jpg

20160207_205255_zpsxopbsgok.jpg


2-11-2016

Started on the intercooler pipework

20160210_164704_zpssjf8ky0w.jpg



Comments

Wow what a build!

Posted by Diggymart on 1/17/20 @ 10:10:34 PM