New HID Retrofit Kit by 2ez24get

To start get a set of headlights. OEM or aftermarket it doesn't matter. I get them new off Ebay for around $100. 

Purchase a HID bulb kit like the one below. You will need the adapter when you install the HID bulbs in the headlight.

http://www.ebay.com/itm/281371346960...%3AMEBIDX%3AIT

Remove the bulbs and headlight rubber grommet. Three screws and be careful when pulling off the rubber not to rip it. 

To get the headlight lens off the body of the headlight you will need to heat the headlight to about 210 degrees several times. It usually take me 3 trips to reheat the headlights. 

Do one at a time. I use a hook carpet razor blade to cut between the lens and the body to cut through the glue. I picked mine up at Harbor Freight.

http://www.harborfreight.com/folding...ife-90802.html

http://www.harborfreight.com/pack-of...des-37557.html

You will need some way to check how hot the headlight is getting. I use a inferred gun. I also use a set of wooden chisels to pry apart the lens from the body. I start near the top of the headlight and pry and cut the glue away until I can get my hands inside to pull apart the two. 

http://www.harborfreight.com/4-piece...set-42429.html

I would recommend you get an entire HID retrofit kit as you need ballast, blubs, HID projectors and wiring harnesses. I recommend 35 watt 2.8" MAX unless you are alright with having to cut away the top of the reflector bowl.

9-10-2014

Pull the DRL fuse and wire the Angel Eyes or LED Tube to be your DRL. I use a DRL harness to run mine.

http://www.ebay.com/itm/LED-Daytime-...ht_3884wt_1362

9-13-2014

The Retrofit kit I would recommend is the G8 HID BI-Xenon Headlights Projectors Lens Kit CCFL Halo + 2 AC Ballast 6000K kit it has all the parts needed to wire up the HID. It's available in Left Hand Drive and Right Hand Drive.

http://www.ebay.com/itm/G8-HID-BI-Xe...ht_9581wt_1362

Package includes:

2x G8 Universal BI-xenon Projectors + CCFL Angel Eye

2x HID bulbs for the projectors (proprietary product)

2x High quality AC/35W slim digital ballasts

2x CCFL Inverters for CCFL Angel Eye

1x H/L relay harness

Other necessary wires and accessories for installation

12 months warranty

More pictures of the process to install the LED Switchback tube in the housing..

I drilled 3 small holes to mount the LED tubes. Glued with epoxy two mounts and one end to secure. Tested LED Tube and amber turn signal. Next is installing the Projector HID in the headlight and installing them on the van to adjust the horizontal cutoff. 

Drill behind where the lens will mount in the groove. 

Attach the mounting clips.

Drill a hole to run the wiring through

60cm LED Switchback Tube

Test the LED Switchback

Epoxy 2 of the clips to the headlight. The lens channel is directly underneath so drilling and mounting screws is not possible. 1 is a full clip and the other is half of a clip. I used JB Weld.

9-28-2014

Finished the HID Install.

Ballast and wiring harness installed.

Applied 5 min black rtv sealer to the housing.

Cleaned the lens inside out. Check it against a bright light to identify and remove streaks.

Taped together and let sit overnight.

Back Side wiring. 

Installed 

Short Video of LED Switchback when turn signal is on. Flashes Amber then switches back to white as a DRL.